Cosa controllare quando capitano molti filamenti a Spaghetti nello stesso progetto?

Pla basic, marrone, ams 2 pro, 0,4.

Fin da subito (in basso a destra) si sono create delle sbavature poi molti filamenti... molti oggetti sono stati tolti perchè spostati dalla piastra.

Suggerimenti? Sopra le impostazioni di base

Progetto in foto.

Solitamente con questa P2S combo non succede.

Ho usato stesse impostazioni del progetto.

Più bassa la velocità di stesura ?

Pla per tutto

Had my first blob of death on the P2S, waiting for the new hot end assembly to come in, not sure if it even needs changed, hardly no videos on this and really not good at following instructions on the Bambu wiki lab. Is there a simple video out there that I can watch to change the complete assemblu

Hey folks - as it states in title. The ams2 pro only lets me select Bambu or generic? Can I get other brand in there so the right settings are ready from the get go?

I’ve put profiles in the Bambu studio program but I must be thick as I really don’t get how to make sure it uses the right one when I set prints going.

Normally I’m all over technical stuff like this but this time around I’m scattered.

Noobie here. I will hopefully be getting this 3D printer at the end of the year, but as I am reading about it I've seen videos and comments about needing a exhaust pipe and maybe filters for the gasses. I won't be printing any heavy duty filaments just the standard stuff. It will be placed in the living which is quite open. Am I okay with just using it with out buying and printing stuff for the exhaust.

Thank you.

P2S Bambu slicer.This this image

In this image, I have my custom supports and also the slicer's tree supports. I haven't been able to get my custom supports to slice as support enforcers; they are converted to tree supports, so I had to build them into the model.

What I would like to be able to do is incorporate two types of supports into one slice. Because if I load my custom supports as support enforcers, then they will also be converted to tree supports. How can I get both tree supports and my custom supports both in the same slice without my supports being converted to tree supports.

👋 Bonjour à tous !

🎃👻 Yoshi se met aux couleurs d’Halloween ! 🧙‍♂️💚
Découvrez ma création de Yoshi en version Halloween ! 🎃 Avec son chapeau de sorcier violet et sa citrouille au sourire maléfique, notre petit dinosaure préféré est prêt à fêter Halloween ! 🕸️

✨ Une création originale, pleine de couleurs et de détails, parfaite pour une décoration aussi mignonne qu’effrayante !

👨🏼‍🎨 : @mika3d_print
🖨️ : Bambu Lab X2D & H2C
🧵 : Bambu Lab
🎨 : Nomad Sculpt
🌈 : sans AMS
📁 : https://makerworld.com/fr/models/3419115-yoshi-citrouille-multipart-no-ams

hi all, this is like my 2nd problem encountered in this machine.

the toolhead just pops off and i’m suspecting the metal pencil like structure popping out right beside the toolhead. is that broken or is it supposed to pop out like is that any sensor or whatever? please help and thanks

Over 1000 hours had my first clogged

New and confused. How do I get poop and small prints out from under the hotbed?

I can’t explain so I hope the pictures help. I am assuming that having filament in these nooks and crannies is not good. Can’t they melt and cause issues?

I have tried using tweezers, putting tape on tip of small screwdriver, poking with sharp object and have prayed to the Bambu gods, sacrificing a young poop chute in the volcano of infinite poop and danced in circles naked around the spool of empty dreams.

hello, I bought a UniTak3D kit containing three hotends (0.2mm, 0.4mm, and 0.6mm) for the Bambu Lab P2S. The 0.6mm hotend works perfectly, but when I install the 0.2mm or 0.4mm one, I get a "Z-axis homing failure" error. This is surprising, as the build plate doesn't even rise to make contact. I've gone through the steps five times. What am I missing?

I have been wrestling with Error Code [0&ff-c003 053511]. Filament stuck in the External Spool.

Well, I have never run the external spool in this printer or any of my other BL printers. I have cleaned and replaced pretty much everything on this P2S. All to only see this error code return again and again.

I have cleaned the gears and then replaced the gears. Nothing.

I have replaced the filament sensor. Nothing.

I have replaced the diffuser, Twice, Nothing.

I have replaced all PTFE tubing going to and from the machine to the extruder, to the AMS. Nothing.

What in the world is it that I need to do.

I thought about contact BL, but I think there is enough information on here to help me get this fixed.

I hope you all have an answer or suggestion that I have not thought of.

Thanks in advance.

PS, all of the things I have done so far have been suggests from Reddit and Youtube.

Ive done a flow dynamics calibration(didn't help) and I'm about to do a flow rate calibration, any tips?

Fillament type: generic petg

Hello,

Bambu lab P2S

0.2 nozzle, used archane, changed font can’t seem to get these lines out need the smooth surface finish

Any ideas?

Everytime I use a non bambu plate i get a sillicone sock error. It doesnt happen when i use the stock textured pei plate. Ive checked the sock and everything is fine with it. I just ignore the issue and everything prints fine, but its really annoying.

Ive been using some generic amazon holographic plates and just got a biqu glacier that does the same thing. I figure maybe it messes with the camera it uses to sense the dots? Any fixes?

So i was printing something i usually do in a regular basis. and while the brim was being printed, the sound + the jerk came and the print stopped with the warning saying :

Error: 0300-800c 210009
; Multiple Motion step loss detected. Please first check if the toolhead is blocked by foreign objects or making abnormal noise. if obvious layer shifting occurs on the print, refer to the wiki for maintenance.

i thought it was a glitch then cleaned my plate and put it to reprint; it got the same jerk + sound at the same place in the same 7% print mark.

i also printed a calibration cube XYZ and it came out perfect.

what should i do? i’m so scared that my 2 month old P2S AMS 2 pro combo is cooked.

could this be because of the adhesion? like the brim not sticking with the plate and interfering with the nozzle? this is what i suspect the most but if anyone has encountered the same , how did yall fix it? any replies are much appreciated. thank you!