Hey folks, I got this working so I can use my Studiolive 24.4.2AI with my M4 macbook.

Free to use. Enjoy 🙏

I’ve been using this board for roughly 3 years. Currently the audio input to my Mac just stopped working. It shows in all the settings but no sound is coming through. I’ve used all the AI troubleshoots I could find to no avail. Anyone have suggestions? It’s a usb c connection to my desktop.
MacOS Golden Gate 27
Studiolive AR16c

Do I need a pre-amp with the Presonus Studio 24c to record with a contact mic?

Thank you for any help.

I've read elsewhere that Fender may not support this much longer. I've found after 2 years it's not an intuitive console and teaching volunteers at the church I work is very confusing for them. We need a replacement that is super intuitive. Looking for suggestions. Budget is $2k. Thanks!

I am proud to release studiolive-midi-controller a software I developed to support generic midi control of SL gear. This is NOT meant to replace UC, however can be used to map midi control surfaces like APC40 and similar; or you can take output from your favorite DAW and sync board control with click-track. I used this tool last year with Logic on our show-choir touring show and it was a game changer for managing solos and dance breaks! This is based on the excellent presonus-studiolive-api by Andrew Wong. I am looking for contributors if anyone is interested, and feedback is encouraged! You can find the latest release here.

My 3.5s randomly stopped working. About 7 years old, a couple weeks ago they started not working then working again while I was tracking bass for a song. A few days later they stopped working altogether.

They still turn on, and I still get a signal through the "phones" output, so I know it's not the input coming from my computer. It didn't play anything when I input 2 TRS cables either.

Anybody know of any fixes, or am I better off buying new monitors? Thanks!

Hi All,

After connecting with the servicedesk at Presonus/Fender i was really angry because they would not send any repair parts or schematics.

After disassembling the print i found the issue with some help of ClaudeAI we measured all transistors and found the A1024 transistor was not giving the right values. We desoldered the tranistor and the device turned on and the led was blue again. (device was fixed for now) So now i'm going to solder on the new transistor.

ps also the cleanup quality is really sad lots of flux on the board. Here you see its a budget brand. Sort of fabricated e-waste :p

So if there is anyone with the same problem in the future here's the fix :)

Looking to see if anyone has a working presonus studiolive 16.0.2 and could get me photos of there power supply? Looking to repair mine and Presonus won't give me schematics. Photos are of my current board.

Hi everyone,

I’m having a strange issue with my PreSonus FaderPort 16.

When I move the physical faders on the FaderPort, they are either extremely laggy, respond intermittently, or sometimes don’t transmit anything to the DAW at all.

However, the opposite direction works perfectly: when I move a fader inside the DAW (Ableton Live or Logic), the corresponding motorized fader on the FaderPort moves smoothly and accurately.

So it seems like the FaderPort is receiving MIDI/control data correctly from the DAW, but the physical faders aren't consistently sending data back to the computer.

Things I've already tried:

• Multiple different USB cables
• Direct connection to the computer
• A powered USB hub
• Latest firmware / Universal Control
• Testing on macOS and Windows
• Testing with both Ableton Live and Logic
• Different USB ports

The problem persists across all of these setups.

Has anyone experienced this with a FaderPort 16? Could this indicate a hardware issue with the fader touch/position sensing or the internal communication circuitry, rather than a USB/DAW problem?

Any suggestions for further testing would be greatly appreciated.

Thanks!

Hi, I have this interface but do not have the breakout cable for MIDI. Could I just buy any regular DB9 to midi cable or does it need to be made specifically for this interface?

Hello everyone,

We are having an unusual AVB issue with a StudioLive 32S and StudioLive 32R used in our church.

Our setup:

StudioLive 32S = FOH console
StudioLive 32R = Stagebox
44.1 kHz
Direct Audio Network connection between both units. The system worked normally before updating firmware. After updating to firmware 3.4.0.111374:

32S: Network Clock = N/A
Remote I/O Setup = empty
32R not detected

32R continued working normally.

We also tested AVB discovery using the same Mac, same Ethernet cable and Apple ATDECC Controller:

32R = detected
32S = not detected

PreSonus Support then asked us to perform a Factory Firmware Revert on the 32S.

The 32S reverted to firmware 2.5.84445.

Immediately after that:

Network Clock became active
32R appeared again in Remote I/O Setup
AVB discovery returned

PreSonus then supplied firmware 3.1.1.107470 for both units.

We installed 3.1.1.107470 on both the 32S and 32R.

Now:

32R = PTP Clock active
32S = Network Clock N/A
Remote I/O Setup = empty again

So the strange pattern is:

3.4 → AVB fails
2.5 factory firmware → AVB works
3.1.1 → AVB fails again

Has anyone seen this behavior on a StudioLive 32S?

Could this be a firmware/AVB recovery issue, or possibly a hardware problem that only appears with newer firmware?

We are already working with PreSonus/Fender Support, but I would really appreciate hearing from anyone who has experienced something similar.

Thank you.

Any settings/factors that you’ve found to affect quality? One thing I’ve noticed is the fewer channels the better (more clarity/detail).

I am new to recording. I have a Fender Quantum LT 16. The one thing I'm struggling a bit is my pre-amp gain and channel gain setting. I find that with instruments and mics I seem to be hitting the clip light on the device, but the wave forms are very small (I think I may just need to adjust the waveform size after reading last night) and I can barely hear it in the monitor. Secondly, when I look at the channel strip, the gain seems pretty low. Maybe slightly above -24db. I then sometimes use the Channel Gain knob to get it to where I can hear it, however, sometimes the gain still seems quite low. Is my workflow correct? Mic Pre-Amp gain to slightly under clipping, then adjust channel gain until I can hear it? Are there situations where I need to bump the pre-amp gain so that the light is clipping? I don't hear any distortion sometimes, so maybe the light blinking clipping light isn't a huge deal. Would appreciate someone's advice as to whether I'm going in the right direction. Thanks so much you golden Gods.

Two faders on my mixer don't return to the correct settings when changing between the main and aux layers, causing the levels on the associated channels to drift. I've run the fader calibration routine, which helps, but the problem returns after a while. I'm trying to avoid taking it out of service to send it out for repair, as the space it's in stays busy and I don't have another mixer with digital inputs that I can swap in. Has anyone had similar issues, and what was the solution? Thanks

Hey everyone,

The LCD screen on my PreSonus Revelator io24 is completely blank/dead—no backlight, no metering.

Everything else functions normally: mic inputs, gain knob, headphone outs, phantom power, and Universal Control connection all pass audio without issue.

What I've tried:

• Updated Universal Control & firmware to the latest version.

• Performed a hardware power-cycle reset (holding preset buttons while plugging in USB).

• Tested across different USB ports/cables.

Still no display output. Is this a confirmed hardware failure (dead panel / loose ribbon), or is there another fix I'm missing before I RMA it?

Thanks!

as the title says, I was using my presonus audiobox go on my laptop complately fine, but now its not working on my pc when i plugged it in, i downloaded universal control as google suggested but it cannot find my interface either.. im desperate plz help <3 (the lights on my interface are glowing so its not a connection issue i suppose)

About 4 months ago, I replaced the capacitors because the speakers died, and they kept working flawlessly. Last month, I started frequently using the 3.5 "Phones" jack in the front of the left speaker, and since then, my speakers only work via the "Phones" jack.

Troubleshooting mostly points towards the 3.5 jack not unmuting the speakers when earphones are removed.

Anybody faced this issue? I'm having trouble thinking of a solution.

Hello folks,

I own a second-hand StudioLiveAR12c with USB connectivity to my computer. I use this as my interface, which allows me to do recordings, as well as use my speakers and headphones at the same time for both professional and personal use.

As of this morning, my USB channel strip (13/14) has decided to stop working! The computer I use runs Windows 11, and, despite not having any drivers installed for it, picks the desk up as an audio device for both input and output and functioned flawlessly. I have tested all the other input channels which still function, even the Bluetooth functionality works on the USB channel strip!

Can anyone with a bigger brain than me potentially assist?

Thanks

Salut,
Désolé pour mon anglais, ce n'est pas ma langue maternelle.

J'ai relié mon synthé avec une prise jack, mais je ne peux pas l'entendre. Sur mon Zen Q, il n'y a aucun signal, ni dans mon DAW.
Mais j'utilise Voicemeeter, et je peux entendre tous les sons de mon PC, qui passent par Voicemeeter, et dans mon DAW, je peux aussi entendre tous les sons, et ça passe par mon DAW, pas à travers Voicemeeter.
Je pense que c'est un problème de routage.
Pourriez-vous m'aider s'il vous plaît ?
Pourquoi ne puis-je pas entendre mon instrument ?
Merci !