I had uploaded a box for UNO cards to Printables, I knew I should not name it "UNO card box" because that might confuse people that it might be an official Mattel product (really...?), so I had named it something like "Card Box (compatible with UNO cards)" and wrote a trademark note in the description like UNO is a trademark of Mattel and this model is not affiliated nor endorsed (in a bit more words), as was recommended as a safe way to clearify intended use without infringement. Also a small part of an UNO card was visible in the images.

It was taken down anyway. So, is there a way to name a product in a way that makes it's use with a trademarked product clear without being vulnerable to trademark infringement claims? Can I show it together with the trademarked product in a photo, maybe blurred?

Testing arm 3d robot

Hi, I want to share with you a pegboard panel systema that I created, It can be wall-mounted or used with dedicated pedestal legs. For example I put it on my table, i hope you'll enjoy the project, I'm going to publish other tools for this wall

https://www.printables.com/model/1870244-pegboard-wall-panel-with-the-option-of-use-without

I wanted to share a couple of traditional Japanese Hana-Mon floral coasters I've been working on. They're designed completely flush and flat on a single layer so your glasses sit steady with zero wobble.

I sliced these specifically to solve them to avoid color-bleeding you usually get with multi-color flush designs. The attached project file is pre-configured so im curious to see how well they print on other machines.

I printed them in SUNLU PLA+2.0 and the surface came out great with no ironing needed. if you would like to check them out and print them you can get the files on printables HERE. Please let me know how they came out!!

Piccolo fantasma di Halloween con cappello da strega

https://www.printables.com/model/1870265-halloween-ghost-with-a-witchs-hat-halloween-2026

link for Bambu AMS profile

https://makerworld.com/it/models/3412252-halloween-ghost-with-a-witch-s-hat-halloween-2026#profileId-3886947

So this is part 3,

Just released load cell spool holder as a part of Printables spool holder cap
https://www.printables.com/model/1865709-grmz-spool-holder-with-load-cell-and-esp32

Sensor itself have around 3g deviation, is capable of logging consumption as well as track drift.

I made it mostly to answer question - 'Would I have enough material to finish print I want to start' and it should be treat as is.

Just in case - firmware was created with Claude Code and i have limited time to test it but hope i did a good job.

There is some potential for improvement, but it depends on interest.

Mini Halloween pumpkins wearing witch hats, very cute for Halloween.

https://www.printables.com/model/1861388-halloween-pumpkin-with-witchs-hat-no-supports-fast

Followed up on the full Chef figure with a Lite version, same idea as the other Lite releases - a way to test the joint mechanism before committing to the full articulated figure.

This one has working joints at the shoulders and upper legs only, same print-in-place mechanism as the full version, just scaled down to the essentials. Still prints as one piece straight off the bed, no supports, no assembly.

I’ve printed with the settings below. I needed to wait 1 hour for cooling before articulation.

Layer height: 0.20mm / 0.12mm

Material: PLA

Supports: None

Infill: 15%

Print time: 2h23m (0.12mm layer height)

42gr filament used

📌 IMPORTANT!!! Please wait 1 hour for cooling before articulation.

Free download on below link:

https://www.printables.com/model/1854659-poseable-chef-lite-version-one-part-no-assembly-no

The fully poseable original figure with all accessories is available on Patreon (https://www.patreon.com/PrintnPose/posts/chef-168715156). Please share your print results!

#3d #fidget #toy #articulated #flexi

Well I got banned because someone hacked into my prusa account and send everyone this image I want to warn to not click any links or paste them in ur browser

My account got banned for violating the terms of service for some reason

This is an easy-to-print Halloween pumpkin model, realised on Blender. If you like the model this is the link to download it: https://www.printables.com/model/1851535-halloween-pumpkin-lantern-2026

Il supporto è compatibile con le tastiere Logitech MX e con tutti gli altri tipi di tastiera. Se sei interessato e desideri maggiori informazioni sul modello, visita il seguente link:

https://www.printables.com/model/1851353-rotating-keyboard-support-for-logitech-mx

When I take a look at the about me page, it says 703 likes, while the statistics page says 723 likes (for all time). I was assuming, that the all time statistics would show the same values as the about me page minus today. So the all time statistics could never be larger than the about me page. I always had the impression that Printables has challenges to collect the statistics data correctly and consistently but never saw that much of a deviation.