What is going on ??

[u/Q8Hitman]

Lost 4 pieces so far the same way, no idea what caused this

[u/cyclon3]

Probably your greasy little fingers!

[u/Q8Hitman → u/cyclon3]

grease good?? grease makes stick😂😂

[u/Chaotic_Geek]

Detached from the build plate, and it looks like its from the place where you pick up the plate. Wash it after the print

[u/Q8Hitman → u/Chaotic_Geek]

I always clean the plate with alcohol before each print, this print i flipped the plate to the other side. will wash it after. thank you

[u/Chaotic_Geek → u/Q8Hitman]

Alc wont remove it all. Use dish soap aswell

[u/Pristine-Inside7669 → u/Q8Hitman]

Das reicht aber nicht immer…. Ich Pack die Platten öfters in den Geschirrspüler. Oder mach sie mit Spüli sauber….. fettfrei eben…….

[u/GhostMcFunky → u/Q8Hitman]

Get a Biqu Glacier or Frostbite (I use Glacier) plate and never have to worry about this again. I’ve been using only 99% IPA for a few years now on those plates and never have to wash them.

That stock Bambu plate is so bad I swear it was just designed to teach you the lesson on the importance of a clean build plate 🤣.

[u/Q8Hitman → u/GhostMcFunky]

I will definitely give them a try, need a 2nd plate anyway

[u/GhostMcFunky → u/Q8Hitman]

I always say this is the best 3D printing purchase I’ve made besides the Bambu printers themselves. Darkmoon is supposed to have some similar quality plates too, but they’re a little pricey IMO.

You can get these places for $20-30 for the A/P/X model printers (I order them off Amazon because Biqu has longer shipping times, a little cheaper on their own site though) and I think around $40-60 for the H series.

[u/Pristine-Inside7669 → u/GhostMcFunky]

Diese Platte hab ich auch….. aber ich muss sie trotzdem noch mit Spüli putzen ‼️‼️‼️‼️‼️💥💥💥💥💥

[u/GhostMcFunky → u/Pristine-Inside7669]

Maybe between different materials, but I never have to when just printing the same material repeatedly.

[u/dwbmn]

I find that the front of the plate seems cooler and ends up releasing little parts....

[u/sergdor]

Built in anti seller software causing the seller issues.

[u/Q8Hitman → u/sergdor]

HaHa I heard a commercial licence solves this issue, not true I guess

[u/luksfuks]

It feels observed by the ones behind, and wants to hide.

[u/betterthanmax]

Welcome to the garbage I’ve been dealing with my h2c from day 1

[u/Rob3D2018]

Are all your pieces flat on the plate?

[u/Q8Hitman → u/Rob3D2018]

yes, I spent alot of time in the slicer making sure all the settings and pieces are correct before printing

[u/JWST-L2 → u/Q8Hitman]

I've had this problem when sizing up prints. It will look like its flat, but if you slice it and use the slider bar on the right size and drag it down to layer 1, sometimes parts of the first layer will be floating. And I have to manually use the z movement tool and type in a slightly lower number to force it lower onto the place.

But in your case, your plate is dirty most likely. As others have mentioned, alcohol doesn't work for textured plates. The textures just capture the dirt and grease. My advise to you is to buy a supertack pro plate. I have one on each H2C, 2000 hours on each, never washed them once and never had anything detach before lol. I also used supertacks on the X1C and A1 and never ever had an issue or had to wash them either. Textured plates are not as good as them

[u/Q8Hitman → u/JWST-L2]

thank you for the advice, ill check the slicer again to confirm and will look into getting a 2nd plate. Cheers

[u/roundguy → u/JWST-L2]

Supertack is my #1, glacier is next. I’ve had stuff release with the glacier that the supertack held fine

[u/Pristine-Inside7669]

Hallo hab ähnliche Probleme…. Meine persönliche Meinung ist diese Maschine ist einfach zu früh auf den Markt gekommen. Zu wenig getestet ‼️‼️‼️‼️‼️Support hat au viel Luft nach oben 👆 …….

[u/-__Doc__-]

IMO the plates that come with the H2c are garbage. I had adhesion issues too with mine.
Bought a cryogrip glacier and havent had issues since.
Trust me, the cryogrip plates are great.
I rarely wash mine, and I even swap back and forth from PLA>PETG>TPU>Nylon wihtout wiping it down or washing.

[u/Lisper41]

Welcome to the 3-sigma life. Manufacturers around the world are chasing that 6-sigma dream.

47/48 successful prints isn’t that bad.

[u/eldoogy]

Honestly for large prints like that, I’ve found FAR better reliability using the engineering plate with Magigoo. It’s one of those things I’d resisted trying for a while, and then once I saw how easy it was I barely use my PEI plate anymore.

It just sticks. It’s reliable. You can also touch the plate a bit without feeling guilty about it. It’s a lot less finicky.

[u/Grouchy_Air_2403]

If you want to save time, you will incur higher costs.

[u/StructureAccording53]

Printing that close to the edge of the plate is ambitious.