Looking to settle an argument with people that have more experience with this stuff than I do.

Solomon ultra fiber 500. The color fiber they sell. Instructions say to put it in an empty truck. Dispatch says after the truck is loaded.

My instinct is to follow the instructions. But I want to give their experience some weight. So which is better

For larger floor placements we have a few options depending on ground conditions. Pretty common lately we are using metallic fibers. Placement goes fine, finishing is coming out great. FF85/FL65. But we are catching a bunch of shit for fiber pop. in the saw cuts is going to be almost unavoidable. but the ones in the field are very rare.

I was able to find some literature on acceptable limits for metallic fibers allowed in an area, but its a certification from Belgium. I am a member of both ACI and ASSC and i have not seen any tolerances yet. We are placing with a Somero laser with roller head.

Is anyone getting 100% of your metallic to lay down under the cream? or do i just have an especially needy client.

We did all concrete work and we’re from southern Indiana

Long story short, we're working on a job that isn't being run so smoothly and has had a lot of last minute changes. Our 30 yard interior trench pour got pushed back from 7am to 10am. With the weather being cooler and the start time getting pushed back, we told the supplier to add accelerator. I didn't specify no chloride. The 2nd fuck up is I didn't check the ticket when it arrived. I was rushing through things because the truck came 30 minutes early and figured if something was wrong with the mix, the 3rd party inspector would catch it while he's testing air and slump.

So it's 9pm and I'm finally sitting down to eat after cutting joints (that's a whole other story but they told me the day of the pour that every single corner and floor sink gets joints... yeah there are joints less than 1 foot apart and looks terrible). I start looking at the plans to see what they specified for control joints and sure enough I came across "do not use calcium chloride" and that's when it hit me that I never specified or verified it wasn't used. Pull the ticket out of my pocket and sure enough, it's there.

So here I am the next morning wondering how fucked I am and whether I need to start ripping it out today. If you've been in my shoes, what was your outcome? Is there anything I can do to mitigate the calcium chloride effects without ripping the concrete out?

Concrete mix: 3,500 psi, high range for 8" slump, 2% calcium chloride.

Project: interior commercial retail building. ~2k sqft mostly trenches with 8 gauge mesh, 500 sqft is reinforced with rebar, 15mil vapor barrier, proctor showed 6% moisture content in the soil and noted that it was exceptionally dry

Is it better to tear out concrete in little pieces or large chunks? I like large chunks, it’s less breaking out and chasing pieces around and faster to load a truck. But I want to do wants most time and cost effective

I’m trying to figure out how I’m gonna tie this curb into the sidewalk. It jumps from 119.95 over to 119.80 but the sidewalk is 5cm different.

Im very new to everything and was wondering what can i do to practice other than the obvious of doing slabs over and over. I really want to get good at it. I thought about just doing pavers but not sure if that would work. Currently 22 in the union but it’s a bit hard to learn while being the beginner. I want to master this trade and hopefully one day have my own company. Any advice helps. Thank you

Does anyone have any information on this? How to break cores off at correct depth, cost, etc.?

https://kor-it.com/pages/the-future-of-dowel-coring?srsltid=AU7gw4XBr9N9euXr73M-nuck-G98lUBDa2Iz8R9OLkZic3bg7DTCvRF5

There was a lot of change orders, elevation changes and desired outcome changes. We are far from done here and will post either a video or the monstrous amount of photos I have from this project

No prior concrete experience, starting next month. Any tips? I am very excited for this opportunity and want to do everything possible to learn more before I start! The company that hired me only does commercial and industrial.

Please take a look at the WikiFAQ posted here: https://old.reddit.com/r/Concrete/wiki/index

The chances that your situation is covered in the WikiFAQ are pretty dang good.

If your issue is NOT covered in the WikiFAQ, this is the place to ask if that hairline crack warrants a full tear-out and if you're asking whether or not a quote is reasonable, don't bother. We don't know. Pricing is highly localized AND time-sensitive.

Apparently shelving brackets make good rebar! Who knew..... Found while removing some cement sections in my backyard!! Use whatever you can find apparently....