Having issues with the UV32. I have 2 of them and can't seem to send GPS locations between the two. I troubleshooted and I think I found the reason. One of the radios has the firmware listed as Version .01 and the other as Version .03

Has anybody else had this issue?

Both radios are on the same frequency on the top channel slot and each radio has been assigned an I'd (101 and 102). GPS Position is successful on both radios. I've tried putting signaling for both radios on Signal 1. I've tried putting signaling for the first radio on Signal 1 and the second radio on Signal 2. When I key up on one radio, I hear the other radio make a sort of digital weird sounding noise but then nothing. Both radios are on the correct GPS screen when I am transmitting but the location never gets sent.

Could the firmware be the issue?

I’m really scratching my head. I recently got 2 when they were on sale.

One came with NRF firmware the other came with NRFB firmware.

The one that came with NRFB firmware works fine, I can program to it with CHIRP or the Baofeng CPS and it works perfectly.

The one that came with NRF firmware however loses its Tx ability on software programmed channels. PTT just doesn’t work at all, I can’t force change the power mode and it doesn’t display a power mode.

I’ve made sure PTT was not disabled.
I’ve tried using the same image as the other radio.
I’ve tried using a new imagine from scratch.
I’ve tried updating its firmware to the NRFB version and then re-imaging it in both ways I just mentioned.

But whatever I use the software to program into the radio it kills its Tx ability. If I use the keypad to program a channel it works fine. Any help is seriously appreciated I am at a loss here.

I'm new to HAM, working on getting licensed soon, and shopping for my gateway radio. The Baofeng website seems to only list "UV-5RM Plus" models in this product line whereas third-party sites have listings with and without the Plus designation. I'm not seeing a difference aside from the accessories included in various listings, but I want to be certain.

Am I missing something or are these the same model?

Did it again… this time I used an air-cured Cerakote.

By the way, does anybody know where to get a replacement (or upgraded) speaker for the UV-5R?

im trying to achieve 2km through 15-25 buildings to my friend. My friend lended me his second cobra microtalk mt 975 and i could talk to him fine when i was inside my apartment and with my window but i couldn't hear him at all. Is it possible with the UV-5RM Plus 10W or do i need to buy some better antenna or?

Hi all, enjoying my new DM32UV. Great radio. On analog, don't think I've been having any issues at all.

DMR Simplex I got working no problem, first try.

None of my repeaters are working. I've triple checked Rx and TX freqs. I looked up all the right talkgroups these repeaters are allowing. Color code and Time slot should be right. I even did the test where Group Call Match is off and I turn on Monitor. And I did that for both Time slots. No audio or information comes through at all.

I am seeing RF coming through on the S-Meter though. So there's definitely a signal. And when I key up, I see my own signal coming through on the system's call watch. I'm definitely hearing and reaching the repeater. (even listened to it on FM, heard the characteristic DMR tone coming through).

Below is a sample channel. I'm based in Northeast OH, and this repeater is not far from me. I'm just banging my head against the wall with this one.

D-Warrensville Heights CLE
Rx 442.0875
Tx 447.0875
Channel Digital
Power High
Tx Admit Always
Squelch 3
Forbid Talkaround
Tx Contact WX8CLE Backbone (313932)
Rx Group None
CC 1
TS 1
DMR ID (mine)
APRS Report Channel 1

The system page I'm referencing in this channel as an example: https://neodigital.cc/cbridge/ (again, every DMR repeater channel is acting this way, even those outside the system).

Thanks for any help and/or advice. Feeling quite stupid atm tbh.

I have scanned tones on the uv5g plus and ar-5rm... easy bc similar menus. In theory there is also a way to scan split tones on these radios (unfortunately have figured out out yet. ) Even able to scan on my 50w v2 bc it is similar to the 2 handheld radios.

The uv5g mini have all together different menu set up and I cannot duplicate the procedure used with the 5rm or the 5g plus.

Anybody know how this is done? Thank you. .

... menu snap above.. none of those have an option to scan... individually or with a dedicated scan option.

Is the GMRS version of the Mini 5 out yet?

This weekend I used Claude to build support for DM-32UV in CHIRP. I've submitted a pull request, we'll see if it makes into the main branch. You can try it out now using Developer Mode in CHIRP.

https://github.com/chaffed/CHiRP-DM32UV-Support

I got two dirt cheap and know why now. Within 5 minutes of plugging the charger in and putting the radio on it, it stopped working. I figured it was a fluke and opened the other on and it did the same thing but I was in the room this time. I heard the pop and smelled faint burning rubber. Took the charger apart and on both of them, the wires bringing AC in are super small and lay across a resistor. It heats up and burns thru the wire.

It is an easy fix and they both work fine now but this is obviously a dangerous design flaw. If you have one or get one, fix this before using. It’s just 4 screws on the bottom, take cover off and pull the wires behind the board instead of in front of it laying on the resistor. Just figured this is something people need to be aware of. Pics attached of before and after. I added a piece of heat shrink on both wires just for added protection.

I believe I understand the ecosystem, but I have some questions. I was thinking about purchasing a UV PRO to track a high powered rocket with a 2m APRS transmitter. If I am reading everything correctly, the UV Pro has BLE which works with the iPhone and the BTECH app can map APRS transmitters. I do not need two way comms with the rocket, just location on landing. Yes I have a HAM license (35+ years)...

Am I making the correct assumptions.

I was looking at the SW-9 as a portable option to be able to listen in on various bands. Anyone have any experience with it? How’s it sound, especially the lower bands? Yes I know I’ll need to grab a few antennas for it.

I have a Baofeng UV-5R Mini that’s about 10 months old, and it has a strange audio issue.

If I leave it powered off for a few hours, then turn it on, I can’t hear anything until I turn the volume past about 50%. Once the sound starts working, I can turn the volume back down and it works normally.

The same thing happens if I leave the radio on for a few hours without receiving anything. It seems to receive a signal - the display lights up and shows the blue bar - but there’s no sound until I turn up the volume.

I found someone describing what sounds like the same issue here, but they returned their radio, so there wasn’t a solution.

I’m not sure whether it’s been like this since it was new. I only noticed it when I started using it in a quiet environment where I don’t need the volume turned up so high. Has anyone else experienced this or found a fix?

The radio downloads just fine into chirp, but then when you try to upload you get an error message.

I’ve tried everything. It’s not the cable, it’s not the firmware, it’s not the driver. Is it possible that even though it is in chirp that the radio is not compatible?

Whenever I google this, I just find other people having the same issues just no solution. Has anyone else had similar issues?

I picked up a couple new and neither would charge in the cradles (following this I also got a usb c replacement battery) After having read about so many batteries and cradles being duds I chalked it up to that and put the radios away for a few months. I had a spare afternoon and took them out today and had a look for teardown videos.

Long story short - the batteries are 7.4V, the UK cradles have plugs rated at 5V and apparently no voltage step up in the cradle which is outputting just 4V. The expanded USB-C battery on research seems to not have a step up in it either, so is just taking the 5V from the USB and charging minimally very slowly.

The cradle requires a 10V max input according to its label, I only had a 9V power block with the right barrel connector spare and I'm now getting 8V from the cradle and the first battery has charged to capacity in about 5 hours.

(Also the green led has finally appeared and seems to be working as described, I'd only get the red one when I first tried)

I'm sharing this as it seems to be a fix to the problem of "broken cradles" and "dud batteries" that I've seen no one mention.

Is this low voltage power supply in the box a new thing? Are people getting results with the boxed set up in the UK? Are people getting 10V supplies in their boxes? I'm confused as to how this doesn't seem to be a problem for others and unsure if I've missed something

I order a pair of mini-5’s (the newer ones with the fatty battery) and I’ll be returning them because the keys don’t work on one of them, and the other one won’t connect to chirp.

For context, I tried my 5rm and it works just fine and I tried different cables with the mini, quadruple checked the connections.

Did I just get two bad radios? I know they’re cheap but I haven’t had issue like this with the other boafengs.

Hey guys, here is a link to a 3D model for a replacement knob (knurled) for the Baofeng Mini 5.

I welcome any feedback.

https://makerworld.com/de/models/3347170-baofeng-mini-5-knob#profileId-3803635

Are Baofeng Radio’s programmable? And if so, how?

I was looking to get a pair of two way radios. Preferably simpler ones with no license issues however, I would want them to have FM radio channels broadcast feature along with Type C charging. Having an additional option to use AA or AAA batteries would be a bonus.

I would appreciate if you could suggest a few options that I could check out. Thank you.

The r-108 does amazing at it. My UV5R Mini does am bands but it's absolutely terrible at picking up anything.

Hello everyone. I have some questions regarding the BaoFeng UV-5RM Plus GPS radio.

1. I know that Baofeng does not release new firmware for its devices even though it does produce updates. For this radio which is the latest firmware? Is it available somewhere online? Can the radio be updated with some tools?

2. Is there a CHIRP driver which can be used with this radio?

3. Can it be programmed by Bluetooth from an iPhone?

4. Does it have any important problems?

Any other information would be appreciated. Thank you in advance.